Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
This article which follows relating to Tools You Need to Install a New Bathtub is particularly insightful. Check it out for yourself and decide what you think of it.
Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately hard task. If the old tub is conveniently obtainable, the task can relocate speedily; if you have to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the task is much harder. In either situation, the project is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your restroom if you have actually already purchased a new bathtub as well as do not need to transform the setup of your previous supply of water pipelines.
Your tools and product list must comprise the following:
Getting ready for the Installment
Firstly, the sustaining framework supplied with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bath tub till the level checks out level.
To mount faucets, fit the bottom of the furthest versatile faucet port to the ideal supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water system as well as inspect all joints and also new pipework for leaks and tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait until the tub has actually been used at the very least once as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in place between the tap and the sink. Safeguard the tap in place with the supplier offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous kind needs to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to problems with wetness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very curious about Tools You Need to Install a New Bathtub and I really hope you enjoyed reading my article. Liked our blog? Please share it. Help someone else discover it. Thank you for your time. Don't forget to visit our site back soon.
Avoid further plumbing damage; call. Report this page